AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |
Back to Blog
Custom stains neveda patina green1/24/2024 ![]() We recommend to apply at least 6 layers of oil and 9 to 12 coats of Nitro and let it cure properly. When applying oil, keep in mind that oil also penetrates the wood and will affect the color. For a smooth finish, you need to sand lightly with 600 grit, be careful at edges!įinish as desired with Nitro or other lacquer types or even oil. Mica is a mineral powder that you can feel on the surface. These traditional pigments have been used for specialty finishes like the old golden archtops, built of layers with bronze and gold. Start a new section a bit above the previous one and connect them by gently rubbing the stain down to the previous section.ħ) After you covered the whole top/sides/back, gently go over it with a paper towel or fine dry sponge.Ĩ) Applying Mica takes some practice especially with larger surfaces.ġ) Apply a second layer to intensify the color, but let the first layer dry completely before applying a second one.Ģ) For a double stain, or combination with the liquid suStain, leave the first coat to dry for at least 30 minutes, sand down till the suStain or the Mica is left in the more open grains. Colors that shine and shimmer with a metallic look We are so excited with our sustain Mica pigment powders and had lots of fun testing them out. Work fast, don’t let a section dry and don’t rub, but work gently.Ħ)Spread till you have an equal coverage. Patina MQ6-38 Behr Paint Colors Patina LRV R G B Save to My Colors Visualize this Color Buy Samples or Gallons SIMILAR COLORS LIGHTER COLORS DARKER COLORS COORDINATING COLORS Our recommended groupings of colors that pair well together. Apply from the center of your section to the outside to avoid any overspill running down the sides. Get free shipping on qualified Green Concrete Stains products or Buy Online Pick Up in Store today in the Paint Department. Ventilate properly.ĥ) Work in sections, for example start at the lowest side and work upwords. Or fill your airbrush and spray an even coat. Green Copper characterizes the much admired blue-green patina that can be found on ancient cathedrals and other copper metal surfaces exposed to weather. Copper Patina® looks excellent from BOTH up close and from a distance. This is the most traditional version of a patina’d copper. This copper paint print looks like a weathered brown copper that has aqua green patina spots on it. If you’re going for an opaque coverage, you can use sanding sealer as per the instructions.ģ) If you have open pores and want to have a completely smooth finish, you can fill the pores with a grainfiller in a color as close to your wood as you can get.ġ) Put on some gloves or get your airbrush or spray gun with a minimum 1mm needle and put on a mask.Ģ) Apply with airbrush, fine sponge, a folded lint-free cloth or a folded strong paper towel.ģ) Shake or stir your mixture well before application.Ĥ)Dab your sponge, cloth or towel with your mixture and gently run it over the surface. Green Copper is a painted product that is designed to look like an old copper roof that has started to patina. Do not use a sanding sealer, as it will also seal the wood and your stain will not penetrate those spots. Sand down to 400 grit in the direction of the grain and free from dust and grease.Ģ) If you have wood that raises its grain when made wet, you may want to wet it with water and sand down those grains. When mixed with Nitro or epoxy and stirred properly, they will not sink before the product is dried.Ģ) Keep track of your mixing ratio, as you may need to scale up.ģ) We suggest to mix with water or alcohol in a ratio of 1:1 to 1:3.Ĥ) When mixed with epoxy resins, we suggest half a teaspoon on 30ml.ĥ) When mixed with Nitro, we suggest a small teaspoon on 30ml.ġ) Make sure your base is well prepared. Your wood will influence the color result.Ĥ) Put on some gloves, get a fine sponge, folded rag, paper towel or get your airbrush, spray gun and mask.ġ) You can mix with water, alcohol, Epoxy and Nitrocellulose, however they will not fully dissolve and will have to be stirred or shaken regularly. And then we have all the possibilities with double stains, combination with our other suStain products or making some accent spots… Let the fun begin!ġ) Envision your design, make a little draft and write down the color pattern.ģ) Get your scrap wood that is comparable to the project you’re going to stain, sand them and remove dust and grease. For more than 20 years I have been recreating the look of ancient bronze on my sculpture and now in this video, I share exactly how to do this stunning finish on any paint-able surface. ![]() The effects that you can achieve with our suStain Mica is stunning, even with a single layer stain. All rights reserved.Time to stain, yes! One of the most fun things to do in your project is staining. Random House Kernerman Webster's College Dictionary, © 2010 K Dictionaries Ltd.
0 Comments
Read More
Leave a Reply. |